电磁兼容技术交流分享

 找回密码
 立即注册

QQ登录

只需一步,快速开始

快捷登录

查看: 7781|回复: 6

FCC标志使用方法 FCC警告语

[复制链接]
发表于 2012-5-5 16:23:06 | 显示全部楼层 |阅读模式

电磁兼容技术交流分享论坛迎您的到来,强烈建议您注册,参与深层次讨论,一起解决繁杂问题!

您需要 登录 才可以下载或查看,没有帐号?立即注册

x
如果是FCC Certification,铭牌上必须有FCC ID
  采用认证方式的设备FCC ID要与设备的其他信息一起标注在铭牌上。对FCC ID号码的表示方式没有特别规定,但FCC建议在ID号码周围划线以将其与其他信息区分开来,如:FCC ID:×××123
  印有FCC ID的铭牌在整个认证过程中可能会被要求修改,为防止浪费,在正式获得认可之前,建议申请人不要大量印刷印有FCC ID的铭牌或在产品上丝印、雕刻等。
设备上的显著位置标有以下这段声明:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  如果设备有两个或多个组成部分,通过线缆连接起来,销售时作为一个整体的,上面的声明只要标在主体控制部分。若设备太小标注的面积不够,上述的声明可写在用户手册或使用说明书的显著位置处,或者标注在设备的包装盒上。
  有意发射机的用户手册或使用说明书还应提醒使用者:未经批准对设备进行改变或修改的话,使用者对设备的使用权利将可能被取消。若用户手册或使用说明书不是以纸质方式提供的,例如是以磁盘或通过互联网等方式提供的,该信息也必须包括在内,以使用户顺利得到该信息。

FCC认证标志使用方法
如果是FCC DOC,铭牌上必须有FCC LOGO:
  如果设备经过测试被证明符合FCC法规的要求,应使用以下标签:

标签格式(符合性声明)
  如果个人计算机是由分别获得认证的部件组装而成,该个人计算机不需再进行测试,使用以下有组装说明的标签:

标签格式,组装(符合性声明)
  若设备太小或将以上标签放在设备上的做法行不通时,例如CPU主板或直插式电路板外设器件,产品标识标签可标在用户手册或使用说明书的显著位置处,但是,唯一的识别信息(商标和型号)和FCC标识必须标在产品上。
  标签不应使用即贴型的纸质标签,标签应该永久性地附着在设备上,并且在消费者购买时能够很容易和清楚地看到该标签。永久性地附着是指把标签上的内容蚀刻、雕刻、压印、丝网印刷或印刷在设备主体上使之不能磨灭,或者将金属、塑料或其它材料制成的标签以焊接、铆接或永久性黏合剂的形式固定在设备主体上。标签的设计还要考虑到设备在环境中的使用寿命。

  A类数字设备或外设的用户使用说明书的显著位置印有以下声明或类似的声明:
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

  B类数字设备或外设的用户使用说明书的显著位置印有以下声明或类似的声明:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
  如果设备是由多个数字设备组成,以上两段声明只需要包含在主控制单元的使用说明书中即可。如果说明书或用户手册不是以纸质方式提供的,而是以磁盘、互联网等方式提供,以上的声明也应以相应方式提供给用户。

FCC警告语
如果是FCC Verification,铭牌和说明书上分别要有警告语:(如果铭牌太小可不加)

  采用验证方式的时候,产品上必须有如下标签:
标签格式(验证)
  该标签必须包括型号(例如:Model. No. 123)、公司名称或商标(Company’s name or trade name)、原产国(Country of origin)的信息。根据美国海关和联邦贸易委员会(Federal Trade Commission)的规定,所有在美国之外生产的产品都必须标明原产国。
  任何情况下,按验证方式的产品标签上都不能出现FCC ID号码。

  标签或产品说明书中应具有相关类似描述:
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.(适用于如Part 73的无线电广播设备等无线电广播接收装置)
This device is verified to comply with Part 15 of the FCC Rules for use with cable television service.(适用于电缆线及其连接器等)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.(其他所有设备)
  注:如果设备是由电线连接的两个或两个以上部分组成,以上标签应加贴在主要控制单元上。如果设备太小,不能加贴以上陈述内容,则必须在设备包装或说明书中体现以上陈述内容。


fcc%E6%A0%87%E5%BF%97.jpg

Untitled.gif
电磁兼容技术交流分享-欢迎您的技术讨论!
发表于 2013-10-26 18:07:44 | 显示全部楼层

What are the labelling and user information requirements for Part 15 and Part...

Publication Number: 784748         Rule Parts: 90         Publication Date: 11/10/2008
Keyword: Part 15, Part 18, Labelling Guidelines, Labelling, Information to User, Information in Manual, User Manual
First Category:        Radio Service Rules
Second Category:        Labelling - Parts 2.925 & 15.19
Question:   What are the labelling and user information requirements for Part 15 and Part 18 devices?

Answer:  
Guidelines for labelling and user Information for Part 15 and Part 18 devices are contained in the below attached document "784748 D01 Labelling Part 15 18 Guidelines v07". Links to 300 ppi artwork for Declaration of Conformity labels are available below:

Examples of Labelling Requirements
Equipment Authorization
FCC Rule Section(s):
Label:
Verification and Certification
§15.19(a)(1) Receivers associated with the operation of a licensed radio service, e.g., FM broadcast under Part 73, land mobile operation under Part 90, etc., shall bear the following statement in a conspicuous location on the device:
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
§15.19(a)(2) A stand-alone cable input selector switch, shall bear the following statement in a conspicuous location on the device:
This device is verified to comply with Part 15 of the FCC Rules for use with cable television service.
§15.19(a)(3) All other devices shall bear the following statement in a conspicuous location on the device:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Additional Labelling For Verification Only
§2.954 Devices must be labelled with a unique identifier.
The identification format shall not be confused with the FCC ID label for certification.
Additional Labelling For Certification Only
§2.925(a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label listing the following: (1) FCC Identifier consisting of the two elements in the exact order specified in Section 2.926. The FCC Identifier shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large enough to be legible without the aid of magnification:
Example: FCC ID AAAXXXXX. AAA=3 Character Grantee Code; XXXXX = Applicant's unique Equipment Product Code (14 characters or less).
Declaration of Conformity
§15.19(b)(1)(i) Products subject to authorization under a Declaration of Conformity shall be labelled as follows:
docparts.gif Print 300 ppi tif files6.7 X 2.8" 3.5 X 1.4" 1.6 X .7"
to download right click and "Save Target As"
§15.19(b)(1)(ii) If a personal computer is authorized based on assembly using separately authorized components: doctest.gif Print 300 ppi tif files6.7 X 2.8" 3.5 X 1.4" 1.6 X .7"
to download right click and "Save Target As"
Part 18 Declaration of Conformity
§18.209(b) Devices authorized under the Declaration of Conformity procedure shall be labelled with:
docsubcert.gif Print 300 ppi tif files6.7 X 2.8" 3.5 X 1.4" 1.6 X .7"
to download right click and Save Target As"
Part 18 Verification
§2.954 Devices subject only to verification shall be uniquely identified by the person responsible for marketing or importing the equipment within the United States:
A uniquely identified label shall not be of a format which could be confused with the FCC Identifier (FCC ID) required on certified equipment or the Declaration of Conformity label. The importer or manufacturer shall maintain adequate identification records to facilitate positive identification for each verified device.
Attachment List:

784748 D01 Labelling Part 15 18 Guidelines v07
电磁兼容技术交流分享-欢迎您的技术讨论!
发表于 2013-10-26 18:14:02 | 显示全部楼层

FCC-Approved Equipment Authorization Labels - Logos of the FCC

FCC-Approved Equipment Authorization Labels
Black Logo on White/Transparent Background
fcc-logo_black-on-white.jpg

Dark Blue Logo on White/Transparent Background
fcc-logo_dark-blue-on-white.jpg

Teal Logo on White/Transparent Background
fcc-logo_teal-on-white.jpg

Light Blue Logo on White/Transparent Background
fcc-logo_light-blue-on-white.jpg

White Logo on Black Background
fcc-logo_white-on-black.jpg

White Logo on Dark Blue Background
fcc-logo_white-on-dark-blue.jpg

White Logo on Light Blue Background
fcc-logo_white-on-light-blue.jpg

White Gradient Logo on Gray Background
fcc-logo_white-gradient-on-gray.jpg

Dark Blue Gradient Logo on Gray Background
fcc-logo_dark-blue-gradient-on-gray.jpg

Teal Gradient Logo on Gray Background
fcc-logo_teal-gradient-on-gray.jpg

Light Blue Gradient Logo on Gray Background
fcc-logo_light-blue-gradient-on-gray.jpg

Black Gradient Logo on Teal Background
fcc-logo_black-gradient-on-teal.jpg

Dark Gray Logo-Wordmark Vertical on White/Transparent Background
fcc-logo-wordmark-vertical_dark-gray-on-white-small.jpg

Dark Gray Logo-Wordmark Horizontal Stack on White/Transparent Background
fcc-logo-wordmark-horizontal-stack_dark-gray-on-white-small.jpg

Dark Gray Logo-Wordmark Horizontal on White/Transparent Background fcc-logo-wordmark-horizontal_dark-gray-on-white-small.jpg

Black Seal on White/Transparent Background
fcc-seal_black-on-white.jpg

Color Seal on White/Transparent Background
fcc-seal_rgb-on-white.jpg

Color Seal (Embossed) on White/Transparent Background
fcc-seal_rgb_emboss-on-white.jpg

Updated: March 22, 2013



http://www.fcc.gov/logos
电磁兼容技术交流分享-欢迎您的技术讨论!
发表于 2013-12-19 21:43:53 | 显示全部楼层
15.19 Labelling requirements.  =====》15.19条款是铭牌的要求
15.21 Information to user. & 15.105 Information to the user. =====》15.21条款还有15.105条款是说明书里面要加的警告语。

说明书里面要加入下面警告语:
caution the user
that changes or modifications not expressly
approved by the party responsible
for compliance could void the
user’s authority to operate the equipment.

A类设备
NOTE: This equipment has been tested and
found to comply with the limits for a Class
A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and
used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.

B类设备
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment
and receiver.
—Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/
TV technician for help.
电磁兼容技术交流分享-欢迎您的技术讨论!
发表于 2013-12-19 21:48:09 | 显示全部楼层

加拿大FCC/IC用户说明书要求

2.6 User Manual Requirements
The applicant is responsible for providing proper instructions to the user of the radio device, and any usage restrictions, including limits of exposure durations. The user manual shall provide installation and operation instructions, as well as any special usage conditions, to ensure compliance with SAR and/or RF field strength limits. For instance, compliance distance shall be clearly stated in the user manual.

The user manual of devices intended for controlled use shall also include information relating to the operating characteristics of the device; the operating instructions to ensure compliance with SAR and/or RF field strength limits; information on the installation and operation of accessories to ensure compliance with SAR and/or RF field strength limits; and contact information where the user can obtain Canadian information on RF exposure and compliance. Other related information may also be included.
Sample as below picture:
1.jpg



http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01904.html
电磁兼容技术交流分享-欢迎您的技术讨论!
发表于 2015-7-20 14:20:09 | 显示全部楼层

RE: FCC标志使用方法 FCC警告语 - §15.19 Labelling requirements.

§15.19   Labelling requirements.

(a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification shall be labelled as follows:

(1) Receivers associated with the operation of a licensed radio service, e.g., FM broadcast under part 73 of this chapter, land mobile operation under part 90, etc., shall bear the following statement in a conspicuous location on the device:

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.


(2) A stand-alone cable input selector switch, shall bear the following statement in a conspicuous location on the device:

This device is verified to comply with part 15 of the FCC Rules for use with cable television service.


(3) All other devices shall bear the following statement in a conspicuous location on the device:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


(4) Where a device is constructed in two or more sections connected by wires and marketed together, the statement specified under paragraph (a) of this section is required to be affixed only to the main control unit.

(5) When the device is so small or for such use that it is not practicable to place the statement specified under paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC identifier or the unique identifier, as appropriate, must be displayed on the device.


(b) Products subject to authorization under a Declaration of Conformity shall be labelled as follows:

(1) The label shall be located in a conspicuous location on the device and shall contain the unique identification described in §2.1074 of this chapter and the following logo:

(i) If the product is authorized based on testing of the product or system; or


                               
登录/注册后可看大图

View or download PDF http://www.ecfr.gov/graphics/pdfs/er09de03.000.pdf


(ii) If a personal computer is authorized based on assembly using separately authorized components, in accordance with §15.101(c)(2) or (c)(3), and the resulting product is not separately tested:


                               
登录/注册后可看大图

View or download PDF http://www.ecfr.gov/graphics/pdfs/er09de03.001.pdf


(2) Label text and information should be in a size of type large enough to be readily legible, consistent with the dimensions of the equipment and the label. However, the type size for the text is not required to be larger than eight point.

(3) When the device is so small or for such use that it is not practicable to place the statement specified under paragraph (b)(1) of this section on it, such as for a CPU board or a plug-in circuit board peripheral device, the text associated with the logo may be placed in a prominent location in the instruction manual or pamphlet supplied to the user. However, the unique identification (trade name and model number) and the logo must be displayed on the device.

(4) The label shall not be a stick-on, paper label. The label on these products shall be permanently affixed to the product and shall be readily visible to the purchaser at the time of purchase, as described in §2.925(d) of this chapter. “Permanently affixed” means that the label is etched, engraved, stamped, silkscreened, indelibly printed, or otherwise permanently marked on a permanently attached part of the equipment or on a nameplate of metal, plastic, or other material fastened to the equipment by welding, riveting, or a permanent adhesive. The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable.

       (c) [Reserved]

(d) Consumer electronics TV receiving devices, including TV receivers, videocassette recorders, and similar devices, that incorporate features intended to be used with cable television service, but do not fully comply with the technical standards for cable ready equipment set forth in §15.118, shall not be marketed with terminology that describes the device as “cable ready” or “cable compatible,” or that otherwise conveys the impression that the device is fully compatible with cable service. Factual statements about the various features of a device that are intended for use with cable service or the quality of such features are acceptable so long as such statements do not imply that the device is fully compatible with cable service. Statements relating to product features are generally acceptable where they are limited to one or more specific features of a device, rather than the device as a whole. This requirement applies to consumer TV receivers, videocassette recorders and similar devices manufactured or imported for sale in this country on or after October 31, 1994.

[54 FR 17714, Apr. 25, 1989, as amended at 59 FR 25341, May 16, 1994; 61 FR 18509, Apr. 26, 1996; 61 FR 31048, June 19, 1996; 62 FR 41881, Aug. 4, 1997; 63 FR 36602, July 7, 1998; 65 FR 64391, Oct. 27, 2000; 68 FR 66733, Nov. 28, 2003; 68 FR 68545, Dec. 9, 2003]

§2.925   Identification of equipment.

(a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label listing the following:

(1) FCC Identifier consisting of the two elements in the exact order specified in §2.926. The FCC Identifier shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large enough to be legible without the aid of magnification.

Example: FCC ID XXXXX123. XXXXXGrantee Code 123—Equipment Product Code

(2) Any other statements or labeling requirements imposed by the rules governing the operation of the specific class of equipment, except that such statement(s) of compliance may appear on a separate label at the option of the applicant/grantee.

(3) Equipment subject only to registration will be identified pursuant to part 68 of this chapter.

(b) Any device subject to more than one equipment authorization procedure may be assigned a single FCC Identifier. However, a single FCC Identifier is required to be assigned to any device consisting of two or more sections assembled in a common enclosure, on a common chassis or circuit board, and with common frequency controlling circuits. Devices to which a single FCC Identifier has been assigned shall be identified pursuant to paragraph (a) of this section.

(1) Separate FCC Identifiers may be assigned to a device consisting of two or more sections assembled in a common enclosure, but constructed on separate sub-units or circuit boards with independent frequency controlling circuits. The FCC Identifier assigned to any transmitter section shall be preceded by the term TX FCC ID, the FCC Identifier assigned to any receiver section shall be preceded by the term RX FCC ID and the identifier assigned to any remaining section(s) shall be preceded by the term FCC ID.

(2) Where telephone equipment subject to part 68 of this chapter, and a radiofrequency device subject to equipment authorization requirements are assembled in a common enclosure, the nameplate/label shall display the FCC Registration Number in the format specified in part 68 and the FCC Identifier in the format specified in paragraph (a) of this section.

(3) For a transceiver, the receiver portion of which is subject to verification pursuant to §15.101 of this chapter, the FCC Identifier required for the transmitter portion shall be preceded by the term FCC ID.

(c) [Reserved]

(d) In order to validate the grant of equipment authorization, the nameplate or label shall be permanently affixed to the equipment and shall be readily visible to the purchaser at the time of purchase.

(1) As used here, permanently affixed means that the required nameplate data is etched, engraved, stamped, indelibly printed, or otherwise permanently marked on a permanently attached part of the equipment enclosure. Alternatively, the required information may be permanently marked on a nameplate of metal, plastic, or other material fastened to the equipment enclosure by welding, riveting, etc., or with a permanent adhesive. Such a nameplate must be able to last the expected lifetime of the equipment in the environment in which the equipment will be operated and must not be readily detachable.

(2) As used here, readily visible means that the nameplate or nameplate data must be visible from the outside of the equipment enclosure. It is preferable that it be visible at all times during normal installation or use, but this is not a prerequisite for grant of equipment authorization.

(e) A software defined radio may be equipped with a means such as a user display screen to display the FCC identification number normally contained in the nameplate or label. The information must be readily accessible, and the user manual must describe how to access the electronic display.

(f) Where it is shown that a permanently affixed nameplate is not desirable or is not feasible, an alternative method of positively identifying the equipment may be used if approved by the Commission. The proposed alternative method of identification and the justification for its use must be included with the application for equipment authorization.

Note: As an example, a device intended to be implanted within the body of a test animal or person would probably require an alternate method of identification.

(g) The term FCC ID and the coded identification assigned by the Commission shall be in a size of type large enough to be readily legible, consistent with the dimensions of the equipment and its nameplate. However, the type size for the FCC Identifier is not required to be larger than eight-point.

[44 FR 17177, Mar. 21, 1979, as amended at 44 FR 55574, Sept. 27, 1979; 46 FR 21013, Apr. 8, 1981; 52 FR 21687, June 9, 1987; 54 FR 1698, Jan. 17, 1989; 62 FR 10470, Mar. 7, 1997; 66 FR 50840, Oct. 5, 2001; 77 FR 43536, July 25, 2012; 80 FR 33441, June 12, 2015]
电磁兼容技术交流分享-欢迎您的技术讨论!
 楼主| 发表于 2018-7-31 09:32:22 | 显示全部楼层

Question: What guidance is available for labeling and user information for ...

Question:
What guidance is available for labeling and user information for RF devices?

Publication Number: 784748

Answer:
Guidelines for labeling and user information for RF devices are contained in the following attachments:
  • 784748 D01 Labeling Part 15 18 Guidelines v09r01 provides general guidance for  labeling and user information.
  • 748748 D02 e labeling v02 provides guidelines for displaying label information electronically (e-label).
Attachment List:

784748 D01 general labeling and notification v09r01
784748 D02 e labeling v02

电磁兼容技术交流分享-欢迎您的技术讨论!
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

专业推荐上一条 /1 下一条

QQ|小黑屋|手机版|Archiver|关于我们|电磁兼容网 ( 粤ICP备15102220号-9 )

GMT+8, 2019-12-6 18:32 , Processed in 0.086166 second(s), 13 queries , APCu On.

Powered by Discuz! X3.4

Copyright © www.emc.wiki

快速回复 返回顶部 返回列表